need ko po suggestion nyo mga MASTER's

[vhinz23]

Good DAy mga Master
meron po kami napiling topic sa Thesis namen need po namen ang suggestion about sa topic namen eto po ang napili nmen
Crack Tiles Detector
   dito po kasi sa batangas meron isang pagawaan ng tiles (MARIWASA) napansin po namin n tao pa ang nag che-check ng crack ng isang tiles..kaya naisip po namen na ito ang i-develop..may sensor po ba na mkakadetect ng crack ng tiles or ano po pedeng sensor.??
degital water dispenser
    ang concept po nito ay parang sa gas station..pano po kaya mag kakakroon ng mechanical concept ito or iba bukod sa electronics..

pede po ba humingi pa ng isang suggest na pang tatlong topic namen kasi po need namen ang tatlong topic...
kami po pala ay Mechatronics Students....


MARAMING SALAMAT PO NG MARAMI SENYO......wait ko po ang reply nyo..

[vhinz23]

reject po ang topic namen...tinawanan lang po kami ng prof. namen...
mga master pa help po may naisip po kami about sa hollow ng tiles, may sensor po kaya para dito or ano ang pedeng sensor dito...

[vhinz23]

eto po ung naisip namen na isa pang topic "automated Fry vat"...eto po ung mga nasa fast food (McDo.jolibee etc) ung lutuan ng fries, gusto sana namen develop gagawin namen automated ung pag taas at pag baba nung lalagyan ng fries or chicken..mag se-set lang kami ng time then after mag end ung time automatic ng tataas ung lalagayan ibig sabihin luto na ung fries or chicken...

pa suggest nman po kung ok lang or mahirap ba or madali lang....mgastos ba to....or mhal...thankz po
ok po ba ung title or mali po ang tawag namen, pa suggest na rin po ng title basta po ganun ung concept..may mga following question din po ako na tatanong about jan..mabuhay po kayo..

ASk ko lang din po kung anong mga gamit ang pedeng gamitin dito...MORE POWER'z mga MASTER's

[e.novacek]

i think the crack tiles detector and the digital water dispenser are all good but lacking of "rigor" .. and i am somewhat quite agreed with your instructor in terms of 'technical' decision that it should be rejected..

i would like to give u a piece of advice vhinz23, creating a thesis topic is not just "to be approved" by your instructor.. i just noticed upon your statements that your not quite sure what you really want to pursue and focused..

Try to do some research and read some scholarly literature on approaches you might take. 

do remember that a thesis need not be an original “contribution to knowledge” .. If you are unsure about the viability of your topic, i suggest to look at past thesis in order to find out what types of projects have been the most successful and you want to push through..

We all know that finding a topic in thesis within an area of interest is more difficult.. but i would like to say this.. the purpose of this process is to formulate a focused and thought-provoking question and to spring your own energies and interest..

"to solve a problem" is a real job of engineer .. so if you want to become a future engineer.. try practicing and solving problems at first stage..

we are here to assist you during the development..

[subzer0]

eto po ung naisip namen na isa pang topic "automated Fry vat"...eto po ung mga nasa fast food (McDo.jolibee etc) ung lutuan ng fries, gusto sana namen develop gagawin namen automated ung pag taas at pag baba nung lalagyan ng fries or chicken..mag se-set lang kami ng time then after mag end ung time automatic ng tataas ung lalagayan ibig sabihin luto na ung fries or chicken...

pa suggest nman po kung ok lang or mahirap ba or madali lang....mgastos ba to....or mhal...thankz po
ok po ba ung title or mali po ang tawag namen, pa suggest na rin po ng title basta po ganun ung concept..may mga following question din po ako na tatanong about jan..mabuhay po kayo..

ASk ko lang din po kung anong mga gamit ang pedeng gamitin dito...MORE POWER'z mga MASTER's

pwede kang gumamit ng pneumatic technology(solenoid valve and probably cylinder) or motor(stepper,servo etc.),maganda ito pero alamin mo muna kung paano at kailan maluluto para alam mo yung timing requirements.pero dahil food ito kailangan yung enclosure stainless na di pwedeng kalawangin at walang screws na mahuhulog dun sa food dispenser or lutuan ng fries.

[vhinz23]

@ e.novacek

thank you po sa magandang comment meron po kaming  napulot na aral..balitaan ko po kayo kung ma approved ung bago nameng topic...sana po guide nyo kami..THANKS


@ icefire

maraming salamat po nabigyan nyo kami ng idea kung pano sisimulan ung naiisip namen.. balitaan ko po kayo kung ma approved un..gagawa pa po kami ng description  about dun sa topic may ilalagay na po kami dahil sa comment nyo..thankz


MARAMING SALAMAT PO MGA MASTER'z .....sana guide nyo po kami..MABUHAY PO KAYO..

[maldihtah13]

to make the fryer cost effective pwede na ang simpleng cable roller at motor dyan. mahal din kasi kung pneumatic pa since the time of raising is not that critical.

[vhinz23]

meron po ba kayong alam na site na merong list ng price ng mga ganyang gamit..?



MABUHAY PO KAYO...

[maldihtah13]

meron po ba kayong alam na site na merong list ng price ng mga ganyang gamit..?



MABUHAY PO KAYO...

Pasyal ka na lang sa egizmo.