Author Topic: to SMD or not SMD... (Read 7005 times)

insomartin · « **Reply #140 on:** May 23, 2011, 07:55:11 PM »

Quote from: drx2k on May 23, 2011, 01:19:34 PM

may list kyo ng commonly used value ng smd resistor, capacitor?

at mabibili sa suking tindahan (e-gizmo) ^_^

hehehe e di same kung anong used mo with thruhole components. gets? kung anong meron sa thruhole of course meron din sa smd.

Philippine Electronics Forum · « **Reply #140 on:** May 23, 2011, 07:55:11 PM »

Richa Yang · « **Reply #141 on:** May 23, 2011, 08:41:08 PM »

what are you talking about here, is it SMD? Do you need? I like to sell also SMD, if you like, by the way, I am Richa Yang from China.

Philippine Electronics Forum · « **Reply #141 on:** May 23, 2011, 08:41:08 PM »

drx2k · « **Reply #142 on:** May 25, 2012, 09:11:54 PM »

nakapag smd na rin sa wakas

pero di gumana yung ckt. dahil sa transistor

pero at least naka pag-try ako ng smd component soldering

Philippine Electronics Forum · « **Reply #142 on:** May 25, 2012, 09:11:54 PM »

PlCUSER · « **Reply #143 on:** May 25, 2012, 10:00:38 PM »

galing!!! great!

Philippine Electronics Forum · « **Reply #143 on:** May 25, 2012, 10:00:38 PM »

Ikasamoko · « **Reply #144 on:** May 25, 2012, 10:06:08 PM »

Marami na sana tayung supplier ng SMD kung di lang natuklaw ng saging si Richa..

Philippine Electronics Forum · « **Reply #144 on:** May 25, 2012, 10:06:08 PM »

e-tronix · « **Reply #145 on:** May 25, 2012, 10:24:57 PM »

Quote from: drx2k on May 25, 2012, 09:11:54 PM

nakapag smd na rin sa wakas

pero di gumana yung ckt. dahil sa transistor

pero at least naka pag-try ako ng smd component soldering

para san yung board nato sir?

Quote from: Kasamiko on May 25, 2012, 10:06:08 PM

Marami na sana tayung supplier ng SMD kung di lang natuklaw ng saging si Richa..

natuklaw ba talga?

tiktak · « **Reply #146 on:** May 25, 2012, 10:41:16 PM »

mukhang pickit2 yung board

Ikasamoko · « **Reply #147 on:** May 25, 2012, 10:49:00 PM »

PICKit Clown nga..

e-tronix · « **Reply #148 on:** May 25, 2012, 11:03:04 PM »

pickit2 ba tlga, mukhang maluwag yung board para sa number of components. tested ba ang clown nato?

drx2k · « **Reply #149 on:** May 25, 2012, 11:05:14 PM »

yup PICKIT2 yan.. clone at simplified

e-tronix · « **Reply #150 on:** May 25, 2012, 11:26:21 PM »

Quote from: drx2k on May 25, 2012, 11:05:14 PM

yup PICKIT2 yan.. clone at simplified

wala yung component for to go prog pla diyan.

tiktak · « **Reply #151 on:** May 26, 2012, 12:00:46 AM »

eto naman yung pangharabas kong pickit2

simplified din, walang protection circuit, walang to go

drx2k · « **Reply #152 on:** May 26, 2012, 12:58:46 AM »

anong code ng smd transistor ang ginamit mo dyan sa pickit 2 clone mo?

tiktak · « **Reply #153 on:** May 26, 2012, 07:50:25 AM »

2SC2712Y(LY) yung NPN at 2SA1162Y(SY) yung PNP, sa e-gizmo ko binili mga general purpose transistors lang naman kelangan, check mo din maigi yung pin config kung tama

Ikasamoko · « **Reply #154 on:** May 26, 2012, 06:50:23 PM »

Yung sakin may MOSFET pa...

Philippine Electronics Forum · « **Reply #154 on:** May 26, 2012, 06:50:23 PM »

Author Topic: to SMD or not SMD... (Read 7005 times)

Philippine Electronics Forum

Philippine Electronics Forum

Philippine Electronics Forum

Philippine Electronics Forum

Philippine Electronics Forum

Philippine Electronics Forum