Author Topic: my Solid State Tesla Coil (SSTC) (Read 8604 times)

RaffT · « **Reply #20 on:** October 09, 2009, 06:14:10 AM »

^tnx

yah mahal nga.. kung bumili pa ako nun, wala na ako pambili ng parts.. hjehehe

dito sa amin meron naman, variac 500VA worth P1500.00

Philippine Electronics Forum · « **Reply #20 on:** October 09, 2009, 06:14:10 AM »

Mhavskie · « **Reply #21 on:** October 09, 2009, 06:31:27 AM »

0T: Saan ako kukuha ng ganon ka laking petot. . Hehe. . Pwede

Philippine Electronics Forum · « **Reply #21 on:** October 09, 2009, 06:31:27 AM »

RaffT · « **Reply #22 on:** November 09, 2009, 10:33:27 AM »

my latest setup

http://i34.tinypic.com/6ro8jr.jpg

driver im using is from miniBRUTE driver..

im using only IRFP450 kaya di gaano malalaki ang arcs.. only 6-7" at best (with 13turn primary, maybe I could DO MORE with lesser turns, maybe 10turns at the risk of blowing MOSFETs) Im not rich so hanggang dito nalang muna ito...

SSTC taken with videocam // reconverted to MPEG4

Philippine Electronics Forum · « **Reply #22 on:** November 09, 2009, 10:33:27 AM »

Mhavskie · « **Reply #23 on:** November 09, 2009, 10:45:18 AM »

Galing talaga ni sir. rafft ang hilig sa mga HV.

Philippine Electronics Forum · « **Reply #23 on:** November 09, 2009, 10:45:18 AM »

RaffT · « **Reply #24 on:** November 09, 2009, 10:56:27 AM »

nakaka ADIK kasi...

para din kasi itong DOG... pag uwi ko sa bahay(esp kung gabi na ako nakaka uwi) eh TURN ON ko ito pampa alis ng stress hehehehe

Philippine Electronics Forum · « **Reply #24 on:** November 09, 2009, 10:56:27 AM »

insomartin · « **Reply #25 on:** November 09, 2009, 11:27:53 AM »

naka helical primary na pala.. hehehe
at parang nakatripod pa!
at bakit parang naka variac na tulad nung kay enyuki?
ASteeeeeg! baka pwede lagyang nang umiikot sa gitna yung parang ion motor???
+1 po sir!!! pa close up po nang ckit! picture lang.

insomartin · « **Reply #26 on:** November 09, 2009, 11:29:07 AM »

ang kulit nang high voltage... kung saan saan pumupunta! pansin ko yung treatment sa coils. ehehhe

RaffT · « **Reply #27 on:** November 09, 2009, 08:35:31 PM »

^tnx sa point

eto pala close-up ng tesla.. ngayun ko lang to napansin kaya ngayon ko lang din ito nai-post

eto yung osc + half-bridge driver..kita rin ang RED straw w/c is the antenna feedback
http://i33.tinypic.com/2zqamn9.jpg

eto naman kasama ang coil.. note 7turns nalang primary, now I could achieve 9" - 10", sometimes 11" ... more than the length of the secondary

NOTE the shiny coil

alagang-alaga yan
http://i34.tinypic.com/qoy637.jpg

eto naman close-up sa oscillator-controller ko..based sa miniBRUTE <google>
http://i35.tinypic.com/oqdds8.jpg

eto naman yung remote interrupter ko, w/c gives variable ON time and frequency (10-100Hz more or less)..
http://i35.tinypic.com/34hgt9w.jpg

bukas ko nalang kunan ng vid.. tinatamad na ako..hehe

insomartin · « **Reply #28 on:** November 09, 2009, 08:43:38 PM »

meron palang perfboard na may solder resist...

RaffT · « **Reply #29 on:** November 09, 2009, 08:50:49 PM »

uu meron.. gaya ng gamit ko dyan .. hehe

n0th1n6 · « **Reply #30 on:** November 10, 2009, 08:40:42 AM »

Galing mo sir Rafft, pogi points sayo.

RaffT · « **Reply #31 on:** November 10, 2009, 06:12:56 PM »

^tnx sa points

this afternoon, kinunan ko ulit ng video.. 5 turns primary nalang and went back to using CT feedback... now I could get 10-11" arcs... di masyado makita sa video (15fps lang) .. this is much SCARIER in real life.. heheh

http://i35.tinypic.com/1zdu03n.jpg

ISSTC reBUILD 2

carlsfootprints · « **Reply #32 on:** November 10, 2009, 11:19:36 PM »

you deserve a point sir rafft..

kaya ko rin kaya magawa yan? hehehe..

Mhavskie · « **Reply #33 on:** November 10, 2009, 11:23:57 PM »

Ako nattry ko gumawa wala nga lang akong HV cap, d bale my +1 sa akin si sis rafft, idol ko yan eh. .Sana ibigay nalang nya sakin ang tesla coil nya. .Hehe

carlsfootprints · « **Reply #34 on:** November 10, 2009, 11:41:52 PM »

parang naiisip ko gumawa nito para sa exhibit eh.. hehe.. kaso baka makakuryente..

madali lang ba gawin yan boss mhav?

Mhavskie · « **Reply #35 on:** November 11, 2009, 12:07:27 AM »

Di ko pa alam di pa ko nakakagawa nyan eh.. Pero gusto ko gumawa mayroon naman ako zvs pero nextime..

insomartin · « **Reply #36 on:** November 11, 2009, 12:49:18 AM »

i really think kaya nyan mag inductive heating din...

RaffT · « **Reply #37 on:** November 11, 2009, 06:27:26 AM »

Guys,

salamat ulit sa points

pwede rin naman gumawa ng 24Vdc or 50Vdc power supply for telsa coil..for exhibits, yun nga lang di gaano malakas ang arcs.. sa akin kasi setup, kapag may bagong "Tweak", I use 35V ac supply , then 75Vac, then 100Vac, then finally 220Vac mains na... always taking note of mosfet heating, para maiwasan ang sira..

plan ko pa nga ito gawin DRSSTC(double resonant) para mas malaki pa ang arcs.. pero bili na muna ako IRFP460, or IGBT...baka di na kayanin ng IRFP450..

ang induction heating, for ZVS flyback driver sya

I always forget to make a video of the "classic" tricks with tesla coil, mainly the holding of florescent bulb and make it light wirelessly.. natry ko na rin, para akong may light saber hehe.. and also the Ion motor..

next time nalang.. hehe

n0th1n6 · « **Reply #38 on:** November 11, 2009, 09:15:31 AM »

Wooow, sir rafft, shoot ka ng video ng madilim

. Isama mo na din yung lightsaber

RaffT · « **Reply #39 on:** November 11, 2009, 11:25:21 AM »

cge..try ko mamaya gabi...

Philippine Electronics Forum · « **Reply #39 on:** November 11, 2009, 11:25:21 AM »

Author Topic: my Solid State Tesla Coil (SSTC) (Read 8604 times)

Philippine Electronics Forum

Philippine Electronics Forum

Philippine Electronics Forum

Philippine Electronics Forum

Philippine Electronics Forum

insomartin

insomartin

insomartin

insomartin

Philippine Electronics Forum