INVITATION FOR COMPETENCY BASED TECHNICAL TRAINING
ATTENTION: GENERAL MANAGER / ENGINEERING MANAGER / CHIEF ENGINEER / HR MANAGER / ELECTRICAL ENGINEERS
“The best way to predict the future is to create it” — Peter Drucker
In order to keep up with the dynamic and challenging engineering profession, continuous education is a must for every professional. Realizing the need to bridge the gap between university learning and industry practice, PAMAVTECH provides hands-on and industry based training.
PAMAV TRAINING INSTITUTE AND TECHNOLOGY CENTER IS NOW OPEN FOR REGISTRATION FOR:
COMPETENCY BASED Training in:
“INSULATION POWER FACTOR FOR POWER TRANSFORMER”
TESDA ACCREDITED (LIMITED TO 15 SEATS ONLY)
Date: FEBRUARY 6, 13, 20 2010 (Every Saturday)
Time: 8:30 AM - 4:30 PM
Venue: 7F Integrated Professional Office building, 14 Quezon Avenue, QC, Philippines
Facilitator: Engr. Rodolfo R. Penalosa, PEE, PECE, APEC Engr.
President and Former, Chairman, Board of Electrical Engineering, PRC Chairman, Technical Panel for Engineering & Technology (TPET) CHED
Course Description:
This practical course provides you with methods and procedures used internationally. Predictive, periodic or condition based (on line diagnostics & monitoring) maintenance are the basis which methodology is applicable. The course includes a novice, or an experienced maintenance technical staff should know to be effective as a test engineer, and for an advanced test engineer to learn new concepts in power transformer testing, filtering, and Interpretation. The course will also focus on issues related to causes of bushing breakdown, arresters, oil impedance, leakage reactance and most of all short circuits rating a transformer can withstand.
BASIC COMPETENCY:
Identifies performance requirements
Presents transformer basics applications, manufacturing and hands on testing on off line power transformer at site
Emphasize methods in insulation power factor testing. Proposes plans on periodic, predictive and condition based maintenance
CORE COMPETENCY:
The course includes a novice, or an experienced maintenance technical staff should know to be effective as a test engineer, and for an advanced test engineer to learn new concepts in power transformer testing, filtering, and interpretation.
Insulator Power Factor COURSE OUTLINE
DAY 1
Transformer Theoretical Basics
1. Transformer Principles
Transformers
Right hand rule, magnetic flux,
magnetic induction
Left hand rule, turns ratio
Transformer losses and types
2. Phasor Diagrams
Operating principles
Operation without load
Operation with load
3. Transformer Classifications, Constructions,
Cooling
Service class, instrument
transformers: current &
potential transformers
§Magnetizing circuits, losses; copper,
hysteresis, eddy-current Efficiency
4. Tap Changers, Standards
ANSI and IEC standards
5. Insulating Oil
Function and oil deterioration
Decay products and sludge
Sampling technique; general safety
technique, oil sampling bottles,
syringe, cautions and
common mistakes
§Nitrogen: total combustible gases,
oxygen
Routine test: color, dielectric
breakdown
voltage, interfacial tension
neutralization number, moisture,
visual
Gas analysis: oxygen
DAY2
1. Transformer Load
Aging of insulation
Analysis of overload curves
Functional life testing
2. Transformer loading guides
Transformer Protection
Overload and over current phenomenon
BIL, withstand capability
Short circuit withstand capability
Overvoltage protection
Overcurrent protection
3. Electrical Test
DC Testing
Insulating resistance
Core ground test
Interpreting the results
AC testing
Power factor: winding, bushing, oil
Turns ration (TTR)
Overall winding insulation
Core excitation
Leakage reactance
Interpretation of results
4. Transformer Maintenance and Applications of
Testing
Frequency of maintenance tests and
repair
Recommended maintenance schedules
Drying out: moisture problems and
heat drying methods, heat and vacuum
methods, determining dry insulation
Service repair
5. Transformer Preventive Maintenance
Load and voltage
Temperature
Liquid level
Pressure – vaccum gage
Dehydrating breathers
Bushing and tap changers Control equipment
Lightning arrester Transformer tanksand joints
DAY 3
Hands-on venue to be announced
Transformer Standards, Specifications,
Design and construction
Transformer manufacturing processes
Transformer Evaluation
Transformer Testing
Basic Application of Apparatus Testing
Understanding Software inputs
Power Factor / Dissipation Factor
Single Phase Excitation
Transformer Turns Ration (TTR)
Leakage Reactance/
Short Circuit Impedance Test
Reserve your seats NOW and SAVE P 1,000.00
(pay on or before January 15, 2010)
Learning Investment for the 3-Days Seminar
Super Saver Rate: P 9,800.00 / seat (Pay on or before January 13, 2010)
Regular Rate: P 10,800.00 / seat (TO LEARN MORE OUR DISCOUNT PACKAGES CONTACT US)
LEARNING INVESTMENT INCLUDES: complete with Learning Manuals/Hand-outs plus a DVD copy, Certificates, plus... AM Snacks, Sumptuous Lunch & PM Snacks!
Seats are limited to 15 – 20 only, so contact us now for registration or inquiries. Look for Chris at telephone (+632)743-3692 (+632)743-3694 / 0917-8075383 or visit our website:
www.pamavtech.com or send an email to
contact@pamavtech.com “The best way to predict the future is to create it” — Peter Drucker
SEE YOU IN OUR SEMINARS
CLME
