caramoan tour package

caramoan tour package

Author Topic: ET-STM32 Stamp Board (STM32F103RET6)  (Read 504 times)

Offline RiDdLeR???

  • Hydroelectric
  • ***
  • Posts: 3032
  • Pogi/Ganda Points: 208
ET-STM32 Stamp Board (STM32F103RET6)
« on: June 26, 2011, 11:49:09 PM »
I'm selling my spare b/new and unused ET-STM32 Stamp Board for Php 1,200.00.  It's slightly more expensive than 25USD as sold by futurlec  ... to compensate for the time, effort, and transpo cost I incurred while looking for the shopfront of the board manufacturer when I had a short work stint in Bangkok last year.  Besides, it will save you the hassle from ordering online and waiting for more than 2~3 weeks and local postal uncertainties.

Reason for Selling:  This is a spare board that has just been kept in storage.  Sayang at nakatengga lang and I need cash to fund other parts I need.

Whats good about this is this board uses an arduino supported 32-bit MCU which is the STM32F103RET6 which now currently has beta support under the Maple IDE.  I still haven'nt tried it though.  There is actually no need for a programmer or jtag since the mcu has a built-in bootloader via UART.  Best of all, all pins are laid out in DIL footprint and is breadboard compatible.

Currently there are two arduino compatible IDEs that support this .... the xduino and maple.

Features

    Includes ST Microelectronics STM32F103 Microcontroller with 512kb Internal Flash Program Memory
    32-Bit ARM Cortex M3 Processor Bit running at 72MHz or 90 MIPS
    Direct In-Circuit Program Download with RS-232 Connection
    Up to 48 I/O points
    16 Channels 12-Bit A/D Converters
    2 Channels 12-Bit D/A Converters
    1 CAN Channel
    5 USARTS and 2 I2C Ports, together with SPI
    Two 32-Bit Timers with Four Capture and Compare Channels
    On-Board Real-Time Clock with External Back-Up Battery Connection
    Power LED and Boot LED's
    Boot Load and Reset Buttons
    Easy to Install and Remove
    Ideal as an Interchangeable Controller for Real-Time Systems

Item includes the stamp board, the rs232 cable and the CD.

I'll post the actual picture later-on.  Hanapin ko muna kung saan ko naitago.



For those interested, I can do meetups on Sundays at Megamall or Podium in the afternoon.  Otherwise, shipping fee to be shouldered by buyer.  Payment via BPI bank deposit.

LBC shipping is around Php 160 nationwide while Air21 is around Php 120 but please check with LBC or Air21 for actual current rates.

Contact:  PM, Call or SMS 0915 876 7695 (I may reply with a different number other than this number).

Philippine Electronics Forum

ET-STM32 Stamp Board (STM32F103RET6)
« on: June 26, 2011, 11:49:09 PM »

Offline RiDdLeR???

  • Hydroelectric
  • ***
  • Posts: 3032
  • Pogi/Ganda Points: 208
Re: ET-STM32 Stamp Board (STM32F103RET6)
« Reply #1 on: June 27, 2011, 10:08:03 AM »
Up lang ulit  .....  I'll just give this till within this week or till funds become available other wise keep ko na lang ulit.  Nanghihinayang din kasi ako dito.

Philippine Electronics Forum

Re: ET-STM32 Stamp Board (STM32F103RET6)
« Reply #1 on: June 27, 2011, 10:08:03 AM »

Offline RiDdLeR???

  • Hydroelectric
  • ***
  • Posts: 3032
  • Pogi/Ganda Points: 208
Re: ET-STM32 Stamp Board (STM32F103RET6)
« Reply #2 on: June 28, 2011, 08:01:09 AM »
Here is the actual picture of my spare ET-STM32 Stamp board.


Here is the pic of the ET-STM32 Stamp board I am using mounted on a breadboard.


I would'nt be online so much in the suceeding days so please just Call or SMS 0915 876 7695 (I may reply with a different number other than this number) or send me an email at alyasngelab[at]gmail.com as it gets autoforwarded to my real email.

For sale only within this week.  If I can secure funds I need earlier, I will retract this offer.

Philippine Electronics Forum

Re: ET-STM32 Stamp Board (STM32F103RET6)
« Reply #2 on: June 28, 2011, 08:01:09 AM »

 

Privacy Policy

Contact Us: elabph@yahoo.com