Author Topic: diy ICD2 clone...anyone? (Read 5459 times)

RaffT · « **on:** June 17, 2008, 08:48:02 PM »

Hi sa lahat!

sino na nakagawa ng diy ICD2 clone dito?? or could anyone post a link??

just want to program 18Fs....

tnx

Philippine Electronics Forum · « **on:** June 17, 2008, 08:48:02 PM »

'yus · « **Reply #1 on:** June 17, 2008, 08:55:48 PM »

di mo pa rin ma-program yung 18F452 mo?

Philippine Electronics Forum · « **Reply #1 on:** June 17, 2008, 08:55:48 PM »

RaffT · « **Reply #2 on:** June 17, 2008, 09:01:04 PM »

di pa rin..error eh.. pero I have been searching sa net..i think ICD(In Circuit Debuger) is for use on PICmicrochip own compiler?? eh pano kaya CCS?

eto nakita ko:

http://users.picbasic.org/projects/ICD/ICD.htm

I think di na yata applicable gumamit pa ng 40MHz clock for the nokia3530 LCD... minsan kasi (sa 16F877 @ 20MHz) nagloloko and LCD during start-up, and WILL need to be reset..either with your PIC or reset lang sa LCD reset line...

hay ewan... I think!? di talaga pwede gamitin ang JDM hardware for burning 18Fs... I have tried 12F675 using JDM, OK sya pag 1t burn mo, pero sa succeeding, WALA na... kelangan mo na imodify mo yung Vdd->Vpp into Vpp->Vdd... sa website ni feng. meron doon(gagawin ko palang)...yung akin kasi, from TE JDM tapos modify ko lang hardware nun para pwede ang Vpp->Vdd(some pcb layout cuts and a 2n7000 mosfet)...

Philippine Electronics Forum · « **Reply #2 on:** June 17, 2008, 09:01:04 PM »

'yus · « **Reply #3 on:** June 17, 2008, 09:13:54 PM »

off-topic:

kahit sa WinPic+JDM? ??
sakin kasi kagabi ko lang na-program yung 18F2550 ko using a JDM-based hardware saka Winpic..
dati di ko rin sya napo-program.. pero may step akong ginawa para gumana 'tong programmer ko..

naka-uncheck muna yung "Vpp" bago ko ikabit ang programmer sa pic (wala munang "Vdd")

Philippine Electronics Forum · « **Reply #3 on:** June 17, 2008, 09:13:54 PM »

marcelino · « **Reply #4 on:** June 17, 2008, 10:02:34 PM »

you might want also to consider yung stolz DIY ICD2 or the inchworm.

yunug stolz version, simple lang ang design. here's the link: http://stolz.de.be/ kahit breadboard ka nalang, pwede yan. meron namang walkthrough sa site nila.

both are are supported by MPLAB, tapos install ka nalang ng CCS para maging compiler mo sa MPLAB.

kung gusto mo programmer lang. basahin mo din yung programmer ng oshonsoft. ang claim nila, supported daw nila ang PIC18F452. (syempre di ko pa natatry.)
http://www.oshonsoft.com/picprog.html However, di nila supported ang PIC18F4520, which is the new version of PIC18F452.

di pa ako nakakagamit ng JDM, siguro dapat gumawa din ako nyan! hehehe

Philippine Electronics Forum · « **Reply #4 on:** June 17, 2008, 10:02:34 PM »

RaffT · « **Reply #5 on:** June 17, 2008, 10:18:04 PM »

@yus,
ah ok.. cge try ko mmya o bukas.. Im busy looking for -other- hardware programmer... btw, I have read from some site, to program -some- PIC, eh tie /PGM to gnd with 100K resisitor..or maybe thats used for LVP?? hhmmmm nkakalito na.

RaffT · « **Reply #6 on:** June 17, 2008, 10:33:43 PM »

yus,

on OPTIONS TAB, checked or unchecked yung raise Vdd before MCLR=Vpp checkbox??

anu setup mo to program that? ICSP ? or not?

'yus · « **Reply #7 on:** June 17, 2008, 10:42:19 PM »

sa options tab naman naka-CHECKED yung "raise Vdd before MCLR=Vpp"..

yung pic ko (soic) in circuit na sya, kahit yung Vdd kumukuha sa programmer..

RaffT · « **Reply #8 on:** June 17, 2008, 10:50:10 PM »

OK i have done the hardware again, board on 452 gets Vdd fro programmer...

hay error parin... pwede step by step kung pano mo pinogram??

'yus · « **Reply #9 on:** June 17, 2008, 10:55:21 PM »

ang idea ata is kelangan enough muna ang Vpp supply bago ikabit yung JDM..
test mo nga kung meron ~13V kung naka-UNCHECKED yung "Vpp"..
sakin merong output yung Vpp kapag naka-uncheck sya (parang baliktad.. hehe)..

RaffT · « **Reply #10 on:** June 18, 2008, 08:15:29 AM »

yus,

anung JDM hardware gamit mo?? yung similar kay feng? or sa TE site?

'yus · « **Reply #11 on:** June 18, 2008, 08:36:16 AM »

ito ang gamit kong JDM-based hardware:

http://www.speedy-bl.com/adapter-e.htm

RaffT · « **Reply #12 on:** June 18, 2008, 11:26:56 PM »

ah ok... pero balak ko rin gumawa pan ikatlo kong JDM programmer, yung may Vpp-then-Vdd...switchable pa...

medyo tinatamad pa ako gawin ito.. hehehe

mArKhAo · « **Reply #13 on:** June 18, 2008, 11:33:54 PM »

nsa magkanu range ng cost ng ganyan?

RaffT · « **Reply #14 on:** June 19, 2008, 06:18:01 AM »

yung posted ko??kung parts lang,not includling the ZIF socket and the connectors to PC, eh mga P50 yata... depende kung ICSP style ko..I dont plan to include IC sockets(para mura), just connectors papunta PIC..

RaffT · « **Reply #15 on:** June 21, 2008, 09:27:42 PM »

Quote from: yus on June 18, 2008, 08:36:16 AM

ito ang gamit kong JDM-based hardware:

http://www.speedy-bl.com/adapter-e.htm

Julz,
I have been looking closely sa scheme na link mo.. anu kaya gamit ng pin6 para sa PC connections?? halos lahat ng mga JDM eh wala nyan.. anyways, gawin ko rin yan.. baka mag hardware ko lang may error kasi ayaw talaga maka program ng 18F452...

hanap na rin ako ng 452 hex LED blinker, para malaman if OK pa itong nga 18Fs ko...

RaffT · « **Reply #16 on:** June 22, 2008, 07:48:55 PM »

eto SERCON2 ko...

gumagana na using F877..yun palang natest ko.. hehe using ICPROG..linagyan ko nalang Vpp and Vdd LED inds...

sino may 18F dyan na DIP?? hehehe

mArKhAo · « **Reply #17 on:** June 30, 2008, 07:36:57 AM »

wow astig ah...
hehe

'yus · « **Reply #18 on:** June 30, 2008, 07:52:21 AM »

off-topic:

pati kulay ng LEDs kapareho ng sercon2 ko:

RaffT · « **Reply #19 on:** June 30, 2008, 08:58:15 AM »

OT ulit:

andyan kana naman..

hahaha at least JUMBO at rectangle LED gamit ko... hahaha

Philippine Electronics Forum · « **Reply #19 on:** June 30, 2008, 08:58:15 AM »

Author Topic: diy ICD2 clone...anyone? (Read 5459 times)

Philippine Electronics Forum

Philippine Electronics Forum

Philippine Electronics Forum

Philippine Electronics Forum

Philippine Electronics Forum

Philippine Electronics Forum