Author Topic: Error during Build (Read 500 times)

tinkerbelldiwata · « **on:** January 16, 2012, 11:07:19 PM »

Hello, people! I was having a trouble building the file created in ZDS II 4.90 version. It appeared like this:

------- projectraks Configuration: Debug -------
[ERROR] Unable to create linker command file. Build aborted.
[ERROR] Unable to create make file. Build aborted.
Build completed.

What will i do? Tulong po..

Philippine Electronics Forum · « **on:** January 16, 2012, 11:07:19 PM »

ΔЅịMø · « **Reply #1 on:** January 19, 2012, 04:48:51 PM »

Na-solve na po ba to?

Philippine Electronics Forum · « **Reply #1 on:** January 19, 2012, 04:48:51 PM »

tinkerbelldiwata · « **Reply #2 on:** January 29, 2012, 10:20:15 PM »

Quote from: ΔЅịMø on January 19, 2012, 04:48:51 PM

Na-solve na po ba to?

Hindi pa po..

Philippine Electronics Forum · « **Reply #2 on:** January 29, 2012, 10:20:15 PM »

ΔЅịMø · « **Reply #3 on:** January 30, 2012, 09:09:54 AM »

Pero, na-compile nyo na po? Baka po kasi during compilation, may error po syang na-meet eh.

Philippine Electronics Forum · « **Reply #3 on:** January 30, 2012, 09:09:54 AM »

tinkerbelldiwata · « **Reply #4 on:** April 12, 2012, 11:22:12 PM »

Quote from: ΔЅịMø on January 30, 2012, 09:09:54 AM

Pero, na-compile nyo na po? Baka po kasi during compilation, may error po syang na-meet eh.

Ok na po ito.. salamat..

dapat pala hindi ko muna in-open yun project sa 5.0 zds II.. sa 4.9 dapat.. i should've installed 4.9 prior to opening the project..

Philippine Electronics Forum · « **Reply #4 on:** April 12, 2012, 11:22:12 PM »

ΔЅịMø · « **Reply #5 on:** April 13, 2012, 09:33:11 AM »

Quote from: tinkerbelldiwata on April 12, 2012, 11:22:12 PM

Ok na po ito.. salamat.. dapat pala hindi ko muna in-open yun project sa 5.0 zds II.. sa 4.9 dapat.. i should've installed 4.9 prior to opening the project..

Aw. Yun lang pala?

Congrats!

tinkerbelldiwata · « **Reply #6 on:** April 15, 2012, 04:38:16 PM »

Quote

[ERROR] Connection Failed. Check power and communication connections.
[ERROR] Target read/write error. (ERR_DTLI_SERIAL_ERROR)
[ERROR] Unable to connect to the target.

pano naman po ito? actually kaka-post ko lang din sa thread ni sir paranz. hindi ko po alam kung ano gagawin ko. feeling ko yung max232 ang problema. sensitive ba yun? i removed it from its esd case. ang ginagamit ko ay debugger from e-gizmo. nag'aalangan ako galawin kasi baka lalong walang mangyari.. tulong naman.. please!!!!!!!!!!!!!

ΔЅịMø · « **Reply #7 on:** April 16, 2012, 09:15:10 AM »

Quote from: tinkerbelldiwata on April 15, 2012, 04:38:16 PM

pano naman po ito? actually kaka-post ko lang din sa thread ni sir paranz. hindi ko po alam kung ano gagawin ko. feeling ko yung max232 ang problema. sensitive ba yun? i removed it from its esd case. ang ginagamit ko ay debugger from e-gizmo. nag'aalangan ako galawin kasi baka lalong walang mangyari.. tulong naman.. please!!!!!!!!!!!!!

Pwede ring yung po yung reason. Baka sira ang MAX232. Try nyo lang po yung debugger nila. Baka gagana yun. 5V lang po yung kailangan sir. Jan din kasi ako nagkakamali eh kaya sunog lahat ng MAX232 ko. Pin config lang po yung tingnan ninyo.

Philippine Electronics Forum · « **Reply #7 on:** April 16, 2012, 09:15:10 AM »

Philippine Electronics Forum