Author Topic: ask ko lang po about arduino (Read 317 times)

wesley14 · « **on:** January 25, 2012, 08:33:03 AM »

may gizduino po kasi ako and gusto ko lang malaman ig pano po yun pag gumawa ako ng project tapos gusto ko na i permanent yung arduino dun?? e di bibili po ako ng maraming guizduino nyan.. meron bang way para yung mismong ATMEGA lang ang gagamitin ko tapos isang programmer lang

Philippine Electronics Forum · « **on:** January 25, 2012, 08:33:03 AM »

insomartin · « **Reply #1 on:** January 25, 2012, 01:32:28 PM »

yup! pwede
http://arduino.cc/en/Tutorial/ArduinoISP

atmega8 na lang gamitin mo since cheaper ito.
may experimenter board din sila sa e-gizmo.

Philippine Electronics Forum · « **Reply #1 on:** January 25, 2012, 01:32:28 PM »

wesley14 · « **Reply #2 on:** January 27, 2012, 02:23:57 PM »

salamat po, ano po pinag kaibna nung dalawang board sa left and right

Philippine Electronics Forum · « **Reply #2 on:** January 27, 2012, 02:23:57 PM »

wesley14 · « **Reply #3 on:** February 02, 2012, 08:30:14 AM »

kelangan po ba talaga tanggalin yung atmega chip sa arduino?? kasi yung nabili ko sa egizmo naka surface mount.

Philippine Electronics Forum · « **Reply #3 on:** February 02, 2012, 08:30:14 AM »

motion55 · « **Reply #4 on:** February 02, 2012, 10:34:54 AM »

Quote from: wesley14 on February 02, 2012, 08:30:14 AM

kelangan po ba talaga tanggalin yung atmega chip sa arduino?? kasi yung nabili ko sa egizmo naka surface mount.

Huwag na kung babaklasin mo din lang galing sa buong Arduino board.

Bumili ka ng AVR IC lang at i-program mo ng bootloader gamit ang Arduino mo pang ISP.

Kaya nga may link pinost is insomartin. Para pang program ng blank IC.

Kung surface mount, solder mo muna sa board mo bago i-program.

Philippine Electronics Forum · « **Reply #4 on:** February 02, 2012, 10:34:54 AM »

Macgyver · « **Reply #5 on:** February 07, 2012, 06:58:40 PM »

Quote from: wesley14 on February 02, 2012, 08:30:14 AM

kelangan po ba talaga tanggalin yung atmega chip sa arduino?? kasi yung nabili ko sa egizmo naka surface mount.

ang pagkakaalam ko kailangan tanggalin otherwise, baka yung nasa onboard ang ma program na chip.

RiDdLeR??? · « **Reply #6 on:** February 07, 2012, 07:43:04 PM »

makikibuhay na rin sa patay .....

Ang siste eh, bili ka ng PDIP na atmega328 IC sa Alexan (di ko lang alam kung meron sa e-gizmo ng atmega328).

You have to program the arduino bootloader sa chip.

But how? Since you already have an arduino/guizduino/aceduino, you are going to use your guizduino as the h/w programmer to program the blank atmega328 IC. You have to upload the AVR ISP sketch to your guizduino.

Ang susundin mong circuit sa link ni boss martin eh yung "Circuit (targeting an AVR on a breadboard)".

Philippine Electronics Forum · « **Reply #6 on:** February 07, 2012, 07:43:04 PM »

Philippine Electronics Forum