sony bravia

[thoniodee13]

mga sirs.. patulong naman po sa kaunaunahan kong aayusin na lcd type.
sony bravia,,

namamatay po sya kusa. tapos stanby continuos blinking yung red light..

ano po kay sira nito?  ayaw ko po kc maghula now pa lang ako magbubukas neto... salamat!

[thoniodee13]

pa up po!!

thanks..

[charile]

wala ba interval ung blinking?

paki check sis ung no. of blinks... compare mo dito.

Sony Blinking Codes
The timing of the blinking you see would be as follows: two to nine blinks, (depending on the fault), about a third of a second apart, then a pause for 3 seconds, then the two to nine blinks about a third of a second apart again.

Here is a list of the problems that might have occurred indicated by the number of blinks. The words in parentheses are those, which you will see for each of these faults on a diagnosis screen described later in this article.
•       Unit is dead, No blinks - Problem in the standby power section. Might check fuse, R607, Q601, IC601, R612 and VDR601 (should show open).
•       Continuous blink once a second, no pausing - No reply from the jungle IC301 (data bus is busy, shorted to ground, or held high), IK video path is defective.
•       One blink - not used for the self-diagnosis
•       Two blinks - B+ over current protection (OCP), unit goes to the standby mode then displays the 2 blink fault. Could be a short in the power supply of any of the circuits.
•       Three blinks - B+ over voltage protection (OVP), unit goes to the standby mode then displays the 3 blink fault. This is also a problem in the power supply circuit, check T603 and R672.
•       Four blinks - No vertical Deflection (V STOP), Screen goes to a single horizontal line then the video signal muted. Check IC1509, Q1505
•       Five blinks - AKB circuit (automatic kine bias), the timer/standby indicator blinks for about 30 seconds then goes to the self-diagnosis function. Something is wrong with the video. Check video out, Q705, 732, 761 and other components on the C board, also check Q218, 219, 220 on the A board. In addition, unit could be in IK blanking, try turning up screen slightly.
•       Six blinks - No Horizontal (H STOP), no raster, goes to the blinking self-diagnosis function immediately. Check C515 & 516 and the jungle IC, IC206.
•       Seven blinks - High voltage shutdown. The high voltage has exceeded 33k and the unit goes immediately into safety shutdown. Check power supply regulation and horizontal circuits.
•       Eight blinks - Problem with the audio (AUDIO), unit goes to standby and blinks the self-diagnosis code. Check IC406 audio amp, PS401, and 402. On some projection models of Sony TV sets, this code means that T8005 (flyback transformer), or the associative components in the high voltage circuits are defective on the D board.
•       Nine blinks - Replace D 6116 and D 6301 on the "G" board, do not re-solder as this will fix the problem temporary. Or Panel Module Error or Thermal Error. If it is intermittent 9 blinks, meaning sometimes the TV comes on and other times you get flashing, then change the switching regulator on the "G" board or check connections. Make sure the regulator is -12 or -13 (negative).
•       Ten blinks - Check Q8014 and Q8013 for shorts, leakage, or bad solder connections on the " D" board. If the transistors are bad, check R8051 and IC8005, also on the "D" board.

[lhan]

mga sirs.. patulong naman po sa kaunaunahan kong aayusin na lcd type.
sony bravia,,

namamatay po sya kusa. tapos stanby continuos blinking yung red light..

ano po kay sira nito?  ayaw ko po kc maghula now pa lang ako magbubukas neto... salamat!

anong model sir

[NORTH LUZON]

anong model sir

nandito na ang master ng mga lcd
pakisagot ang tanung sis ts

[panyero]

patambay lang.

[danny]

sana matuto ako mag repair ng mga LCD at plasma
cge tambaymuna ako dito

[noman75]

makitambay din muna...

ilang blinks pala nakita mo TS?

[RhUNhA]

pa sub din para madagdagan  ang kaalaman

[thoniodee13]

eto po ang model mga sis. klv-32ex300

pasensya na po na bc ako kanina....

observation ko po.

noon sabi sa akin ng may ari. namamatay daw sandali lang magamit.
pag kauwi ko nga sa unit.
mahirap e on pero may standby at pag press sa power mag change ng green yung led pero wala picture totaly wala pong picture ni ilaw wala po..

kahapon nga pag kauwi ko sa unit. na e on ko pero sandali lang mamatay na agad..
ngayon ayaw na talaga mag on.

pag press ko ng power naka green lang pero wala picture.

kapag po nasumpong na mag on. kapag mamatay hindi sya mag stanby sa red.
mamatay po na naka green led po sya.


salamat mga sis..

[samiel]

mostly sa ganyan modelo ex series...yung board sa sensor sa remote ang may problem,binabagsak yung clock data nya,remedy nyan is to replace the sensor board...try mo tnaggalin yung sensor board....parang factory defect yan...kac b4 when i was sa service pa,SOP namin napapalitan agad yung sensor board na yan kac it cause,with green light but no picture and sound,minsan pagpower mo mag on cya,pero yung volume nya sobrang taas nasa 225..pagmataas yung volume need mo lang i factory reset sa menu pro sabay palit muna ng sensor board para hindi babalik.

[noman75]

^ ayos to,, andito pala taga service cen dito kundi ako nagkakamali very nice tips!! dagdag kaalaman ito, dahil jan +1 ka sakin sis may 1 pogi point kana

[brucetech]

galing mo sis samiel,, nice explanation... plus 1 ka din sakin..

[panyero]

mostly sa ganyan modelo ex series...yung board sa sensor sa remote ang may problem,binabagsak yung clock data nya,remedy nyan is to replace the sensor board...try mo tnaggalin yung sensor board....parang factory defect yan...kac b4 when i was sa service pa,SOP namin napapalitan agad yung sensor board na yan kac it cause,with green light but no picture and sound,minsan pagpower mo mag on cya,pero yung volume nya sobrang taas nasa 225..pagmataas yung volume need mo lang i factory reset sa menu pro sabay palit muna ng sensor board para hindi babalik.

welcome sis.good info.

[NORTH LUZON]

meron ako dito same unit
LCD lang ang sira
@ts
saan ang place mo?

[Min]

mostly sa ganyan modelo ex series...yung board sa sensor sa remote ang may problem,binabagsak yung clock data nya,remedy nyan is to replace the sensor board...try mo tnaggalin yung sensor board....parang factory defect yan...kac b4 when i was sa service pa,SOP namin napapalitan agad yung sensor board na yan kac it cause,with green light but no picture and sound,minsan pagpower mo mag on cya,pero yung volume nya sobrang taas nasa 225..pagmataas yung volume need mo lang i factory reset sa menu pro sabay palit muna ng sensor board para hindi babalik.

wow...very nice info. dagdag kaalaman. +1 ka