Gizduino 168 or 328?

[JojoD818]

Ok ANITO is just like Arduino pero may customized IDE and will be one of the collaboration project of PHILROBOTICS

as for GIZDUINO and ARDUINO we are same NEWBIE

Kung may spare cash ka bili ka na din ng Universal Trainer from E-GIZMO GIZDUINO

I believe Sis Akhen is also working with some s exercise manula for it

Thanks for the info master!

Well, Arduino or Gizduino will be my first try with microcontrollers. I was so amazed by the amount of support and tutorials I found in the net, fits well to noobs like me. I'm not new to electronics, but I'm so alien with MCUs.

Yep I saw the Universal Trainer ni Sis Akhen in another thread, ganda at mukhang kumpleto na. The Universal Trainer will have to wait until next month (next 15th payday ), sabay na sa pasukan ng mga bata lahat ng gastos ko sir hehehe...

[Kaizer03]

Gawa yan nila sir. PhilRobotics version of ARDUINO ata. Tama po ba master supremo?

again, its an arduino inspired project.. it was developed by the members of philrobotics from scratch(hardware, software and firmware library)



Sample Program:

Code: [Select]

unsigned int uiTimerToggleLED = 0; //Create a Variable,
   
  void init()  //Initialization
  {
       /* Builtin components doesnt need to configure Pin Direction */
       setPinLow(LED1); //set Builtin LED to Low
       setPinLow(LED2);
       setPinHigh(LED3); //set Builtin LED to High
       setPinHigh(LED4);
 
       setPinOutput(PIN0); //set Pin0 to Output
       setPinInput(PIN1); //set Pin1 to Input
       setPinHigh(PIN0);  //set Pin0 High (Output Logic 1)
       setPinHigh(BUZZER); //set Builtin Buzzer High (Enable/turn on)
 
       uiTimerToggleLED = getTimeMs();  //Initialize Timer, get Current time in milliseconds
  }
 
  void program() //Main User Program
  {
       if(getElapsedTimeMs(uiTimerToggleLED) >= 1000){ //Check if 1s lapsed
               togglePin(LED1);  //Toggle Builtin LEDs
               togglePin(LED2);
               togglePin(LED3);
               togglePin(LED4);
 
               uiTimerToggleLED = getTimeMs();  //Reset Timer
       }
       
       if(isPinLow(SW1)) //Check builtin Button1 State (Active Low)
       {
               setPinLow(BUZZER); //set Builtin Buzzer Low (Disable/turn off)
       }
       else if(isPinLow(SW2)){ //Check builtin Button2 State (Active Low2
               setPinHigh(BUZZER); //set Builtin Buzzer High (Enable/turn on)
       }
       
       if(isPinLow(PIN1)){ //Check Input Pin1 State (Active Low)
               setPinLow(PIN0); //set Pin0 Low (Output Logic 0)
       }
       else{
               setPinHigh(PIN0); //set Pin0 High (Output Logic 1)
       }
  }



[JojoD818]

wow very nice! 

[Mayor Johnaray]

OT

Sis JojoD818... ikaw ba yung na feature sa Philippine Star yung CNC machine? nakita ko kasi sa ibang POST mo JDLABS

[JojoD818]

OT

Sis JojoD818... ikaw ba yung na feature sa Philippine Star yung CNC machine? nakita ko kasi sa ibang POST mo JDLABS

Master Supremo... Yup ako nga yun na feature sa Philippine Star and my diy CNC machine.

[Mayor Johnaray]

^ Natuwa ako at nakalagay din doon na bumibili ka din ng parts sa EGizmo

teka bakit di ka namin maabutan doon

[JojoD818]

^ Natuwa ako at nakalagay din doon na bumibili ka din ng parts sa EGizmo

Yup, yun mga stepper motor drivers ko at parallel port breakout board from eGizmo yan sir!







Minsan na ako nasiraan ng isa (X-axis) kaya bumili ako ulit sa eGizmo, nagkataon naman na dala ko yun sira and pwede pala ipa-repair so yun ang babalikan ko sabay bili ng Gizduino...

teka bakit di ka namin maabutan doon

From Valenzuela pa kasi ako sir, napapadaan lang ako ng eGizmo pag pumapasok ako ng Makati sa www.diyAudio.com, head engineer at chief for special projects ako doon. Kaya usually opening pa lang sa eGizmo nandun na ako sir hehehe...

[JojoD818]

got my Gizduino 328 this afternoon! yeebah!