Author Topic: aeolus 8500 hotair (Read 335 times)

khyleeric · « **on:** June 16, 2012, 10:22:29 PM »

mga bosing tanung q lng po, yung indicator nya sa heater hnd na po nagbiblink anu kya problema nun pero umiinit pa nman po...

Philippine Electronics Forum · « **on:** June 16, 2012, 10:22:29 PM »

insomartin · « **Reply #1 on:** June 16, 2012, 10:31:23 PM »

pundido yung indicator?

gawin mo muna analysis mo. check mo temperature kung nag reregulate.
kung kaya mong gawan nang partial schematic diagram. i post mo dito

Philippine Electronics Forum · « **Reply #1 on:** June 16, 2012, 10:31:23 PM »

??? · « **Reply #2 on:** June 16, 2012, 10:35:36 PM »

ano kaya ito? yung sa soldering iron?

Baka pundi lang indicator or kailangan ireseat.

Philippine Electronics Forum · « **Reply #2 on:** June 16, 2012, 10:35:36 PM »

khyleeric · « **Reply #3 on:** June 16, 2012, 10:37:26 PM »

ok pa sir yung indicator nya..bihira po kc gamitin yun, nung ginamit ko ulit ganun na po ngyari hndi n gumagana yung indicator nya

Philippine Electronics Forum · « **Reply #3 on:** June 16, 2012, 10:37:26 PM »

Ikasamoko · « **Reply #4 on:** June 17, 2012, 01:13:14 AM »

Try mo yung heater adjust from minimum, med then high if ma adjust mo..if yung heater nya is from min at max kaagad..sira yung X2 cap mo..

Philippine Electronics Forum · « **Reply #4 on:** June 17, 2012, 01:13:14 AM »

enriz622 · « **Reply #5 on:** June 17, 2012, 07:48:48 AM »

subs..

khyleeric · « **Reply #6 on:** June 17, 2012, 08:50:10 AM »

gnun b sir... san ba banda malpit yung cap na yun sir?

Ikasamoko · « **Reply #7 on:** June 17, 2012, 03:34:05 PM »

Kunan mo ng pic yung board mo...

ito yung cap sa board ko...

turotoknis · « **Reply #8 on:** June 17, 2012, 04:33:55 PM »

sub

yung sken nmn sinisinok yung blower pero ok n ngayon, wl nmn ako gnawa di ko lng siya gnamit ng matagal (share lng) kkkkkkkkkkkk

??? · « **Reply #9 on:** June 17, 2012, 07:38:29 PM »

hmmm ganyan din sakin di ko ginagamit madalas paggamit ko uli ganun na, low at high settings na lang.

Sis kasamiko ano tawag dun sa cap na pinangpalit mo?

Ikasamoko · « **Reply #10 on:** June 17, 2012, 07:55:57 PM »

Palitan mo lang ng mylar same value at least 275VAC. Yung sakin pull-out ko from horizontal section ng sirang TV..

??? · « **Reply #11 on:** June 17, 2012, 08:57:34 PM »

Ay ganun ba, akala ko polyesterene cap pa kailangan. +1

Subukan ko kasi 473 value nya pero 403 na lang daw ayun sa component tester. Yung isa mas mababa ang read value.

Ikasamoko · « **Reply #12 on:** June 17, 2012, 09:16:20 PM »

Ok lang yan...try mo lang...check mo rin yung pulled-out mo if anu value..

khyleeric · « **Reply #13 on:** June 18, 2012, 05:28:00 PM »

mga bosing pasensya d q pa nbukasn yung hot air q medyo bc e update q kayo pg ok na po..sir salamat ng marami sa info..dhil dyan my pts ka po skin...

Philippine Electronics Forum · « **Reply #13 on:** June 18, 2012, 05:28:00 PM »

Author Topic: aeolus 8500 hotair (Read 335 times)

Philippine Electronics Forum

Philippine Electronics Forum

Philippine Electronics Forum

Philippine Electronics Forum

Philippine Electronics Forum

Philippine Electronics Forum