Author Topic: mobot using logic cnu po my alm??? (Read 13267 times)

jogz44 · « **Reply #60 on:** June 01, 2011, 07:48:42 PM »

boss tik tak may alternative transistors ba yung h-bridge wala kasi yung iba dito baka po meron iba...

Philippine Electronics Forum · « **Reply #60 on:** June 01, 2011, 07:48:42 PM »

e-tronix · « **Reply #61 on:** June 01, 2011, 10:57:57 PM »

TIP series or mosfet. e-gizmo.com sa knila ka bumili pwedi karin magtanung sa technical nila via YM tapos suggest nila sayo ang pwdi sa kailangan mo.

Philippine Electronics Forum · « **Reply #61 on:** June 01, 2011, 10:57:57 PM »

jogz44 · « **Reply #62 on:** June 04, 2011, 07:32:03 PM »

tnx po....^^ kailangan ko na po kasi, try ko nlng po yung mga tip series...

Philippine Electronics Forum · « **Reply #62 on:** June 04, 2011, 07:32:03 PM »

gg22 · « **Reply #63 on:** August 17, 2011, 04:06:50 PM »

pwd po pa2long...???pano po ba gamitin ung sensors ng mouse pra gwa ng wall avoidance mobot???

Philippine Electronics Forum · « **Reply #63 on:** August 17, 2011, 04:06:50 PM »

tiktak · « **Reply #64 on:** August 17, 2011, 04:45:05 PM »

modulate the TX to 38-40Khz then use a tone decoder on the RX side

Philippine Electronics Forum · « **Reply #64 on:** August 17, 2011, 04:45:05 PM »

coejayson · « **Reply #65 on:** March 21, 2012, 11:14:05 AM »

pwde po ba yang diagram na pinost nio if ang gamiting pamalit sa sensor nia ay motion sensor? ung susunod sya sa motion?

ystufeed · « **Reply #66 on:** September 13, 2012, 01:42:22 AM »

Quote from: creedcradle on February 20, 2008, 02:10:36 PM

YEheyyyy!! BEAM kamo?

i made this 3 years ago .. galing sa basura...

line following robot yan..
LM324
NAND/AND gate
OR GATE
12 transisitors
a couple of resistor and capacitor

kung gusto mas kumplikado na BEAM bot, dagdagan mo ng obstacle avoidance/collsion detection circuit

-creedcradle

ystufeed · « **Reply #67 on:** September 13, 2012, 01:47:05 AM »

kua pde po b p send din po s email ko ung circuit diagram nung line follower? thnx

nympha · « **Reply #68 on:** September 13, 2012, 02:58:14 AM »

ung design ni sir tiktak best reference jan. Dun rin namin nagrefer nung gumawa kami ng line follower using logic, pero ung samin lang diretso na sa h-bridge ung output ng comparator, minodify lang namin ung steering. Luckily gumana naman

tiktak · « **Reply #69 on:** September 13, 2012, 09:09:20 AM »

^Iba na ulit ang track may tunnels na din

ystufeed · « **Reply #70 on:** September 15, 2012, 03:07:58 PM »

hello po! pde po b magtnong, ung trimpot po b at ung trimmer pareho lng? kailangan ko po kac ng 10k trimpot eh wla po akong mbilhan pero meron po akong 10k trimmer and 10k potentiometer pde po bang pmalit un? thnx.....

nympha · « **Reply #71 on:** September 15, 2012, 05:37:51 PM »

@tiktak, yes sir un prinovide ng dost hehe

@ystufeed pde parehas lang un. pareho lang clang variable resistors mgkaiba lng ng packaging and obviously size,

basta mgkapareho cla ng value

ystufeed · « **Reply #72 on:** September 15, 2012, 08:58:22 PM »

Quote from: Rk17 on September 15, 2012, 05:37:51 PM

@tiktak, yes sir un prinovide ng dost hehe @ystufeed pde parehas lang un. pareho lang clang variable resistors mgkaiba lng ng packaging and obviously size, basta mgkapareho cla ng value

thnx po tlaga sir Rk17,,,,

nympha · « **Reply #73 on:** September 17, 2012, 03:25:52 PM »

no prob! sana mapagana nyu dn gudluk!

Philippine Electronics Forum · « **Reply #73 on:** September 17, 2012, 03:25:52 PM »

Author Topic: mobot using logic cnu po my alm??? (Read 13267 times)

Philippine Electronics Forum

Philippine Electronics Forum

Philippine Electronics Forum

Philippine Electronics Forum

Philippine Electronics Forum

Philippine Electronics Forum