Author Topic: cp to pc interfacing (Read 1469 times)

>>>vhinz08<<< · « **on:** November 12, 2008, 09:44:48 AM »

pa help naman po! marami naka post about this topic but, kailangan q po very basic at detailed interfacing para q po ma gets, triple A pa lng po me...

ano po ba software at type of connector at unit ng cp kailangan? pwede po ba 32xx or 33xx para mas acessable.

Ang gusto q po mangyari ung pwede makarecive ng message ang pc q through my cp or vice versa, in short pwede sila mag interconnect....

tnx in advance..

Philippine Electronics Forum · « **on:** November 12, 2008, 09:44:48 AM »

zer0w1ng · « **Reply #1 on:** November 12, 2008, 09:55:19 AM »

gnokii http://www.gnokii.org/
It is customizable to what you will want to do.

Philippine Electronics Forum · « **Reply #1 on:** November 12, 2008, 09:55:19 AM »

SpongeBob · « **Reply #2 on:** November 12, 2008, 10:00:19 AM »

Quote from: vhinz08 on November 12, 2008, 09:44:48 AM

pa help naman po! marami naka post about this topic but, kailangan q po very basic at detailed interfacing para q po ma gets, triple A pa lng po me...

ano po ba software at type of connector at unit ng cp kailangan? pwede po ba 32xx or 33xx para mas acessable.

Ang gusto q po mangyari ung pwede makarecive ng message ang pc q through my cp or vice versa, in short pwede sila mag interconnect....

tnx in advance..

mahirap sa yo ang 33xx kasi FBUS protocol yan, gamit ka ng 6210 kasi Hayes ang gamit

Philippine Electronics Forum · « **Reply #2 on:** November 12, 2008, 10:00:19 AM »

>>>vhinz08<<< · « **Reply #3 on:** November 12, 2008, 01:31:07 PM »

ok! tnx po mga sir! pero pa help naman po if papano gagawin, meron po ba kau step by step procedure?

Philippine Electronics Forum · « **Reply #3 on:** November 12, 2008, 01:31:07 PM »

zer0w1ng · « **Reply #4 on:** November 12, 2008, 01:37:15 PM »

You need to know and program in C language to modify the source according to your specifications.

Philippine Electronics Forum · « **Reply #4 on:** November 12, 2008, 01:37:15 PM »

>>>vhinz08<<< · « **Reply #5 on:** November 12, 2008, 01:41:30 PM »

yup! me knowledge po me bout C language! but i have no basic idea kung papano po gagawin! tnx po...

ano po ba dapat 1st step na gawin q?

tnx po...

zer0w1ng · « **Reply #6 on:** November 12, 2008, 02:29:39 PM »

First you should know the what you need or requirements (the problem and solution).
Then you could analyze what part of the code to change or improve based on your requirements.
You could not go to the next step without knowing first what you what to do.

These are parts of the steps software development process (waterfall model):
Requirements
Design
Implementation
Verification
Maintenance

See here for more info http://en.wikipedia.org/wiki/Software_development_process

maldihtah13 · « **Reply #7 on:** November 12, 2008, 02:51:41 PM »

Start with aquiring the unit (6210) ang dlr3p cable.

Use hyperterminal to test your setup after that you can now develop your program.

>>>vhinz08<<< · « **Reply #8 on:** November 12, 2008, 02:57:37 PM »

what i want is kung pwede po mkahingi ng mga source code, at same time schematic diagrams para magkaroon po me ng idea, la pa po kc me idea eh, kahit ung pag connect lng ng cp to pc, no po ba port ang gamit? parallel, serial o usb po ba?

tnx po...

sana d kau magsawa sakin.... je je je..

zer0w1ng · « **Reply #9 on:** November 12, 2008, 03:03:25 PM »

Source code is on the site I posted above.
For the connection, buy a nokia datacable to connect to the PC.
This is connected via serial port.
If you want to make your own see here http://www.panuworld.net/nuukiaworld/hardware/cables/fbus.htm

>>>vhinz08<<< · « **Reply #10 on:** November 12, 2008, 03:12:04 PM »

thnx po mga sir!
GOB Bless....

Philippine Electronics Forum · « **Reply #10 on:** November 12, 2008, 03:12:04 PM »

Philippine Electronics Forum