mga masters patulong naman po,.. gusto ko kasing gumawa nito.. very noob po ako about pic or microcontroler.. pero medyo may konting background po ako sa programming.. anu pong microcontroler ang pwede.. at paanu ko magagawa to.. salamat po
#include <16F84A.h>#FUSES NOWDT //No Watch Dog Timer#FUSES XT //Crystal osc <= 4mhz for PCM/PCH , 3mhz to 10 mhz for PCD#FUSES NOPUT //No Power Up Timer#FUSES NOPROTECT //Code not protected from reading#use delay(clock=32768)#include "N3310LCD.c"short RTCC_flag;#int_RTCCvoid RTCC_isr(void) { RTCC_flag = TRUE; //fires every 1sec}void main(){ int sec,min,hour; nokia_init(); setup_timer_0(RTCC_INTERNAL|RTCC_DIV_4); //overflow every 1 enable_interrupts(int_RTCC); enable_interrupts(GLOBAL); while(true) { if(RTCC_flag) { RTCC_flag = FALSE; sec++; if (sec >= 60) { sec=0; min++; if(min >= 60) { min=0; hour++; } } } nokia_gotoxy(0,0); printf(nokia_printchar,"\f%u:%u:%u",hour,min,sec); }}
/////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////*Graphic LCD Nokia 3310 (LPH7779) routines v3CCS compilerby Michel Bavin 2004 --- bavin@skynet.be --- http://users.skynet.be/bk317494/ ---august 29, 2004*/// ex://// ...// nokia_init();// ...// nokia_gotoxy(0,0);// printf(nokia_printchar,"test???");// ...////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////#define nok_sclk pin_b4#define nok_sda pin_b3#define nok_dc pin_b2#define nok_cs pin_b1#define nok_res pin_b0char char_row,charsel,charpos,chardata; // for nokia_3310 lcdint16 ddram;//char plot_value;int32 plot_value32;int32 plot_umsb,plot_lmsb,plot_ulsb,plot_llsb;BYTE const TABLE1[240]= { 0x00,0x00,0x00,0x00,0x00, // 20 space ASCII table for NOKIA LCD: 96 rows * 5 bytes= 480 bytes 0x00,0x00,0x5f,0x00,0x00, // 21 ! 0x00,0x07,0x00,0x07,0x00, // 22 " 0x14,0x7f,0x14,0x7f,0x14, // 23 # 0x24,0x2a,0x7f,0x2a,0x12, // 24 $ 0x23,0x13,0x08,0x64,0x62, // 25 % 0x36,0x49,0x55,0x22,0x50, // 26 & 0x00,0x05,0x03,0x00,0x00, // 27 ' 0x00,0x1c,0x22,0x41,0x00, // 28 ( 0x00,0x41,0x22,0x1c,0x00, // 29 ) 0x14,0x08,0x3e,0x08,0x14, // 2a * 0x08,0x08,0x3e,0x08,0x08, // 2b + 0x00,0x50,0x30,0x00,0x00, // 2c , 0x08,0x08,0x08,0x08,0x08, // 2d - 0x00,0x60,0x60,0x00,0x00, // 2e . 0x20,0x10,0x08,0x04,0x02, // 2f / 0x3e,0x51,0x49,0x45,0x3e, // 30 0 0x00,0x42,0x7f,0x40,0x00, // 31 1 0x42,0x61,0x51,0x49,0x46, // 32 2 0x21,0x41,0x45,0x4b,0x31, // 33 3 0x18,0x14,0x12,0x7f,0x10, // 34 4 0x27,0x45,0x45,0x45,0x39, // 35 5 0x3c,0x4a,0x49,0x49,0x30, // 36 6 0x01,0x71,0x09,0x05,0x03, // 37 7 0x36,0x49,0x49,0x49,0x36, // 38 8 0x06,0x49,0x49,0x29,0x1e, // 39 9 0x00,0x36,0x36,0x00,0x00, // 3a : 0x00,0x56,0x36,0x00,0x00, // 3b ; 0x08,0x14,0x22,0x41,0x00, // 3c < 0x14,0x14,0x14,0x14,0x14, // 3d = 0x00,0x41,0x22,0x14,0x08, // 3e > 0x02,0x01,0x51,0x09,0x06, // 3f ? 0x32,0x49,0x79,0x41,0x3e, // 40 @ 0x7e,0x11,0x11,0x11,0x7e, // 41 A 0x7f,0x49,0x49,0x49,0x36, // 42 B 0x3e,0x41,0x41,0x41,0x22, // 43 C 0x7f,0x41,0x41,0x22,0x1c, // 44 D 0x7f,0x49,0x49,0x49,0x41, // 45 E 0x7f,0x09,0x09,0x09,0x01, // 46 F 0x3e,0x41,0x49,0x49,0x7a, // 47 G 0x7f,0x08,0x08,0x08,0x7f, // 48 H 0x00,0x41,0x7f,0x41,0x00, // 49 I 0x20,0x40,0x41,0x3f,0x01, // 4a J 0x7f,0x08,0x14,0x22,0x41, // 4b K 0x7f,0x40,0x40,0x40,0x40, // 4c L 0x7f,0x02,0x0c,0x02,0x7f, // 4d M 0x7f,0x04,0x08,0x10,0x7f, // 4e N 0x3e,0x41,0x41,0x41,0x3e // 4f O}; BYTE const TABLE2[240]= { 0x7f,0x09,0x09,0x09,0x06, // 50 P 0x3e,0x41,0x51,0x21,0x5e, // 51 Q 0x7f,0x09,0x19,0x29,0x46, // 52 R 0x46,0x49,0x49,0x49,0x31, // 53 S 0x01,0x01,0x7f,0x01,0x01, // 54 T 0x3f,0x40,0x40,0x40,0x3f, // 55 U 0x1f,0x20,0x40,0x20,0x1f, // 56 V 0x3f,0x40,0x38,0x40,0x3f, // 57 W 0x63,0x14,0x08,0x14,0x63, // 58 X 0x07,0x08,0x70,0x08,0x07, // 59 Y 0x61,0x51,0x49,0x45,0x43, // 5a Z 0x00,0x7f,0x41,0x41,0x00, // 5b [ 0x02,0x04,0x08,0x10,0x20, // 5c 0x00,0x41,0x41,0x7f,0x00, // 5d 0x04,0x02,0x01,0x02,0x04, // 5e 0x40,0x40,0x40,0x40,0x40, // 5f 0x00,0x01,0x02,0x04,0x00, // 60 0x20,0x54,0x54,0x54,0x78, // 61 a 0x7f,0x48,0x44,0x44,0x38, // 62 b 0x38,0x44,0x44,0x44,0x20, // 63 c 0x38,0x44,0x44,0x48,0x7f, // 64 d 0x38,0x54,0x54,0x54,0x18, // 65 e 0x08,0x7e,0x09,0x01,0x02, // 66 f 0x0c,0x52,0x52,0x52,0x3e, // 67 g 0x7f,0x08,0x04,0x04,0x78, // 68 h 0x00,0x44,0x7d,0x40,0x00, // 69 i 0x20,0x40,0x44,0x3d,0x00, // 6a j 0x7f,0x10,0x28,0x44,0x00, // 6b k 0x00,0x41,0x7f,0x40,0x00, // 6c l 0x7c,0x04,0x18,0x04,0x78, // 6d m 0x7c,0x08,0x04,0x04,0x78, // 6e n 0x38,0x44,0x44,0x44,0x38, // 6f o 0x7c,0x14,0x14,0x14,0x08, // 70 p 0x08,0x14,0x14,0x18,0x7c, // 71 q 0x7c,0x08,0x04,0x04,0x08, // 72 r 0x48,0x54,0x54,0x54,0x20, // 73 s 0x04,0x3f,0x44,0x40,0x20, // 74 t 0x3c,0x40,0x40,0x20,0x7c, // 75 u 0x1c,0x20,0x40,0x20,0x1c, // 76 v 0x3c,0x40,0x30,0x40,0x3c, // 77 w 0x44,0x28,0x10,0x28,0x44, // 78 x 0x0c,0x50,0x50,0x50,0x3c, // 79 y 0x44,0x64,0x54,0x4c,0x44, // 7a z 0x00,0x08,0x36,0x41,0x00, // 7b 0x00,0x00,0x7f,0x00,0x00, // 7c 0x00,0x41,0x36,0x08,0x00, // 7d 0x10,0x08,0x08,0x10,0x08, // 7e 0x78,0x46,0x41,0x46,0x78 // 7f}; BYTE const DIGITS_8x16[160]={ 0xfc, 0xfe, 0xfe, 0x06, 0x06, 0xfe, 0xfe, 0xfc, 0x7f, 0xff, 0xff, 0xc0, 0xc0, 0xff, 0xff, 0x7f, //0 0x00, 0x18, 0x1c, 0xfe, 0xfe, 0xfe, 0x00, 0x00, 0x00, 0x00, 0xc0, 0xff, 0xff, 0xff, 0xc0, 0x00, //1 0x3c, 0x3e, 0x3e, 0x06, 0x86, 0xfe, 0xfe, 0x7c, 0xe0, 0xf0, 0xfc, 0xff, 0xcf, 0xc7, 0xc1, 0xc0, //2 0x1c, 0x1e, 0x9e, 0x86, 0x86, 0xfe, 0xfe, 0xfc, 0x78, 0xf8, 0xf9, 0xc1, 0xc1, 0xff, 0xff, 0x7e, //3 0x00, 0xf0, 0xfe, 0x7e, 0xfe, 0xfe, 0xfe, 0x00, 0x3f, 0x3f, 0x37, 0x30, 0xff, 0xff, 0xff, 0x30, //4 0xfe, 0xfe, 0xfe, 0xc6, 0xc6, 0xc6, 0xc6, 0x86, 0x71, 0xf1, 0xf1, 0xc0, 0xc0, 0xff, 0xff, 0x7f, //5 0xfc, 0xfe, 0xfe, 0xc6, 0xc6, 0xde, 0xde, 0x9c, 0x7f, 0xff, 0xff, 0xc0, 0xc0, 0xff, 0xff, 0x7f, //6 0x06, 0x06, 0x06, 0x86, 0xe6, 0xfe, 0x7e, 0x1e, 0x80, 0xf0, 0xfe, 0x3f, 0x07, 0x01, 0x00, 0x00, //7 0x7c, 0xfe, 0xfe, 0x86, 0x86, 0xfe, 0xfe, 0x7c, 0x7e, 0xff, 0xff, 0xc1, 0xc1, 0xff, 0xff, 0x7e, //8 0xfc, 0xfe, 0xfe, 0x86, 0x86, 0xfe, 0xfe, 0xfc, 0x78, 0xf9, 0xf9, 0xc1, 0xc1, 0xff, 0xff, 0x7f //9};//void nokia_init(void);void nokia_write_command(char bytefornokia_command);void nokia_write_data(char bytefornokia_data);void nokia_write_dorc(char bytefornokia);void nokia_gotoxy(int8 xnokia, int8 ynokia);void nokia_erase_y(int8 ynokia);void nokia_erase_x(int8 xnokia);void nokia_printchar(int8 cvar);void nokia_clean_ddram(void);void table_to_nokialcd(void);void nokia_plot(int8 xnokia,int8 plot_value8);void nokia_write_data_inv(char bytefornokia_data_inv);void nokia_clear_screen(void);void nokia_clear_xy(int8 xnokia, int8 ynokia);void nokia_print_uparrow(void);void nokia_print_downarrow(void);void nokia_print_leftarrow(void);void nokia_print_rightarrow(void);void nokia_print_degree(void);void nokia_print_lowbatdegree(void);void display_digit(unsigned char line, unsigned char column, unsigned char digit);///////////////////////////////////////////////////////////////////////////////////////////////////////////////////void nokia_init(void){ output_high(nok_dc); // bytes are stored in the display data ram, address counter, incremented automatically output_high(nok_cs); // chip disabled output_low(nok_res); // reset chip during 250ms delay_ms(10); // works with less..... output_high(nok_res); nokia_write_command(0x21); // set extins extended instruction set nokia_write_command(0xc2); // Vop v1: 0xc8 (for 3V)// v2: 0xa0 (for 3V) // v3: 0xc2 (2v6-5v) ******************************************************************************************************************** nokia_write_command(0x13); // bias nokia_write_command(0x20); // horizontal mode from left to right, X axe are incremented automatically , 0x22 for vertical addressing ,back on normal instruction set too nokia_write_command(0x09); // all on nokia_clean_ddram(); // reset DDRAM, otherwise the lcd is blurred with random pixels nokia_write_command(0x08); // mod control blank change (all off) nokia_write_command(0x0c); // mod control normal change}////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////void nokia_clean_ddram(void){ nokia_gotoxy(0,0); // 84*6=504 clear LCD for (ddram=504;ddram>0;ddram--){nokia_write_data(0x00);}}////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////void nokia_write_command(char bytefornokia_command){ output_low(nok_dc); // byte is a command it is read with the eight SCLK pulse output_low(nok_cs); // chip enabled nokia_write_dorc(bytefornokia_command); output_high(nok_cs); // chip disabled}/////////////////////////////////////////////////////////////////////////////////void nokia_write_data(char bytefornokia_data){ output_high(nok_dc); output_low(nok_cs); // chip enabled nokia_write_dorc(bytefornokia_data); output_high(nok_cs); // chip disabled}//////////////////////////////////////////////////////////////////////////////////void nokia_write_dorc(char bytefornokia) // serial write data or command subroutine{ char caa; for (caa=8;caa>0;caa--) { output_low(nok_sclk); // delay_us(2); if ((bytefornokia&0x80)==0){output_low(nok_sda);} else {output_high(nok_sda);} output_high(nok_sclk); bytefornokia=bytefornokia<<1; }}//////////////////////////////////////////////////////////////////////////////////void nokia_gotoxy(int8 xnokia, int8 ynokia) // Nokia LCD 3310 Position cursor{ nokia_write_command(0x40|(ynokia&0x07)); // Y axe initialisation: 0100 0yyy nokia_write_command(0x80|(xnokia&0x7f)); // X axe initialisation: 1xxx xxxx}//////////////////////////////////////////////////////////////////////////////////void nokia_erase_y(int8 ynokia){ nokia_gotoxy(0,ynokia); printf(nokia_printchar," ");}//////////////////////////////////////////////////////////////////////////////////void nokia_erase_x(int8 xnokia){ char column; for (column=0;column!=6;column++){ nokia_gotoxy(xnokia,column); nokia_write_data(0x00); nokia_write_data(0x00); nokia_write_data(0x00); nokia_write_data(0x00); nokia_write_data(0x00); nokia_write_data(0x00); }}//////////////////////////////////////////////////////////////////////////////////void nokia_printchar(int8 cvar) // Write 1 character to LCD{ charsel=cvar; table_to_nokialcd();}//////////////////////////////////////////////////////////////////////////////////void table_to_nokialcd(void) // extract ascii from tables & write to LCD{ if (charsel<0x20)return; if (charsel>0x7f)return; for (char_row=0;char_row<5;char_row++) { // 5 bytes if (charsel<0x50){charpos=(((charsel&0xff)-0x20)*5);chardata=TABLE1[(charpos+char_row)];} // use TABLE5 else if (charsel>0x4f){charpos=(((charsel&0xff)-0x50)*5);chardata=TABLE2[(charpos+char_row)];} // use TABLE6 nokia_write_data(chardata); // send data to nokia } nokia_write_data(0x00); // 1 byte (always blank)}///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////void nokia_plot(int8 xnokia,int8 plot_value8){ char i; plot_value32=0; plot_value32|=1; // unremark this if you want dotgraph instead of bargraph for (i=0;i!=plot_value8;i++){ //plot_value32|=1; // remark this if you want dotgraph instead of bargraph plot_value32<<=1; } //plot_value32|=2; // bottom line is always filled plot_llsb=(plot_value32&0xff); plot_ulsb=((plot_value32>>8)&0xff); plot_lmsb=((plot_value32>>16)&0xff); plot_umsb=((plot_value32>>24)&0xff); nokia_gotoxy(xnokia,1); nokia_write_data_inv(plot_umsb); nokia_gotoxy(xnokia,2); nokia_write_data_inv(plot_lmsb); nokia_gotoxy(xnokia,3); nokia_write_data_inv(plot_ulsb); nokia_gotoxy(xnokia,4); nokia_write_data_inv(plot_llsb);}////////////////////////////////////////////////////////////////////////////////////////////////////////////////////void nokia_write_data_inv(char bytefornokia_data_inv){ char caa; output_high(nok_dc); output_low(nok_cs); // chip enabled for (caa=8;caa>0;caa--) { output_low(nok_sclk); delay_us(2); if ((bytefornokia_data_inv&0x01)==0){output_low(nok_sda);} else {output_high(nok_sda);} output_high(nok_sclk); bytefornokia_data_inv=bytefornokia_data_inv>>1; } output_high(nok_cs); // chip disabled}////////////////////////////////////////////////////////////////////////////////////////////////////////////////////void nokia_clear_screen(void){ nokia_erase_y(0); nokia_erase_y(1); nokia_erase_y(2); nokia_erase_y(3); nokia_erase_y(4); nokia_erase_y(5);}////////////////////////////////////////////////////////////////////////////////////////////////////////////////////void nokia_clear_xy(int8 xnokia, int8 ynokia){ nokia_gotoxy(xnokia,ynokia); nokia_printchar(" ");}////////////////////////////////////////////////////////////////////////////////////////////////////////////////////void nokia_print_uparrow(void){ nokia_write_data(0x04); nokia_write_data(0x02); nokia_write_data(0x7f); nokia_write_data(0x02); nokia_write_data(0x04); nokia_write_data(0x00);}//void nokia_print_downarrow(void){ nokia_write_data(0x10); nokia_write_data(0x20); nokia_write_data(0x7f); nokia_write_data(0x20); nokia_write_data(0x10); nokia_write_data(0x00);}//void nokia_print_leftarrow(void){ nokia_write_data(0x08); nokia_write_data(0x1c); nokia_write_data(0x2a); nokia_write_data(0x08); nokia_write_data(0x08); nokia_write_data(0xf8);}//void nokia_print_rightarrow(void){ nokia_write_data(0x08); nokia_write_data(0x08); nokia_write_data(0x2a); nokia_write_data(0x1c); nokia_write_data(0x08); nokia_write_data(0x00);}//void nokia_print_degree(void){ nokia_write_data(0x00); nokia_write_data(0x06); nokia_write_data(0x09); nokia_write_data(0x09); nokia_write_data(0x06); nokia_write_data(0x00); // nokia_printchar(" ");}//void nokia_print_lowbatdegree(void){ nokia_write_data(0x00); nokia_write_data(0x06); nokia_write_data(0x0f); nokia_write_data(0x0f); nokia_write_data(0x06); nokia_write_data(0x00); // nokia_printchar(" ");}////////////////////////////////////////////////////////////////////////////////////////////////////////////////////void display_digit(unsigned char line, unsigned char column, unsigned char digit){ unsigned char i; if (line<1 && line>5) return; if (column >74) return; if (digit>9) return; nokia_gotoxy(column, line-1); for(i=0; i<8; i++) nokia_write_data(DIGITS_8x16[digit*16+i]); nokia_gotoxy(column, line); for(i=8; i<16; i++) nokia_write_data(DIGITS_8x16[digit*16+i]); }
panu po ang circuit nito?.. pwede po bng supply nya eh 5v..
^sis marce, nice one... pwede add-on feture... pakilagay naman AM/FM tapos SNOOZE function
try ko pong simulate ung project ni sir yus... eh may error po naghahanap ng dll ung sa lcd..
nakahanap na po ako at nailagay ko na sa library at models.. ganun pa rin po?.. panu kaya to..
