Author Topic: 3d illustrations (Read 9821 times)

insomartin · « **Reply #140 on:** November 16, 2010, 12:25:45 AM »

i'll stick to commercial softwares.

i like open source but it's "makalikot"
sir pro-engineer try nyo gumamit nang blender.

Philippine Electronics Forum · « **Reply #140 on:** November 16, 2010, 12:25:45 AM »

your most RIDICULOUS man :) · « **Reply #141 on:** November 16, 2010, 08:07:08 AM »

yah...

Philippine Electronics Forum · « **Reply #141 on:** November 16, 2010, 08:07:08 AM »

insomartin · « **Reply #142 on:** November 16, 2010, 10:13:22 AM »

^ pa yah yah ka jan. maginstall ka jan! hehehe.

Philippine Electronics Forum · « **Reply #142 on:** November 16, 2010, 10:13:22 AM »

Lito Sapinoso · « **Reply #143 on:** November 17, 2010, 02:00:29 PM »

Quote from: Pro-Engineer on November 15, 2010, 11:42:13 PM

i suggest using open-source software. most of them are at-par with commercial ones. so why bother w/ bootlegs?

Sir, can you suggest a good one?

Philippine Electronics Forum · « **Reply #143 on:** November 17, 2010, 02:00:29 PM »

insomartin · « **Reply #144 on:** November 17, 2010, 02:10:30 PM »

Quote from: Lito Sapinoso on November 17, 2010, 02:00:29 PM

Sir, can you suggest a good one?

blender...
then again the learning curve is... exponential.

Philippine Electronics Forum · « **Reply #144 on:** November 17, 2010, 02:10:30 PM »

Woots29 · « **Reply #145 on:** November 17, 2010, 03:32:39 PM »

^pa expo-exponential ka jan...di pa diretsahing "mahirap!"

insomartin · « **Reply #146 on:** November 17, 2010, 03:35:51 PM »

Quote from: Woots29 on November 17, 2010, 03:32:39 PM

^pa expo-exponential ka jan...di pa diretsahing "mahirap!"

fine fine! log na lang. hehehehehe. hirap talaga mag blender. ok sya pero really not por me. back to solidworks...

Woots29 · « **Reply #147 on:** November 17, 2010, 04:22:22 PM »

may demo ba jan sa inventor?

Lito Sapinoso · « **Reply #148 on:** November 17, 2010, 07:34:36 PM »

Mmmmm, blender looks good enough. I just downloaded a copy but will try it a little later. Dami pa trabaho e.

your most RIDICULOUS man :) · « **Reply #149 on:** November 21, 2010, 08:47:44 PM »

Pano pala pag save ng rendered video dito sa 3ds max

Woots29 · « **Reply #150 on:** November 21, 2010, 09:09:30 PM »

^hmm nagbibiro ka ba?

your most RIDICULOUS man :) · « **Reply #151 on:** November 22, 2010, 01:44:56 AM »

Quote from: Woots29 on November 21, 2010, 09:09:30 PM

^hmm nagbibiro ka ba?

kinda...

hehe... di ko makita kanina nakasingle frame lang pala

May bad

Woots29 · « **Reply #152 on:** November 22, 2010, 06:58:24 AM »

madaling pag-aralan ang 3ds max

Philippine Electronics Forum · « **Reply #152 on:** November 22, 2010, 06:58:24 AM »

Philippine Electronics Forum